
AC extension cable – 100m roll (2.5mm2 – single phase – 2 core)
High quality, flexible 2 core, 2.5mm2 cabling perfect for single phase rooftop AC cable runs. Couples well with Enphase Q-Cable.
High quality, flexible 2 core, 2.5mm2 cabling perfect for single phase rooftop AC cable runs. Couples well with Enphase Q-Cable.
High quality, flexible 4 core and earth, 2.5mm2 cabling perfect for three phase rooftop AC cable runs. Couples well with Enphase Q-Cable.
25mm screw fitting. Required to be installed with all solar rooftop isolators to comply with latest AS5033 standards.
Ferrite core for use in suppressing electrical noise to improve Power Line Carrier (PLC) communications. Suitable for use on Enphase Microinverter systems
ACSolar
Warehouse
EXCLUSIVE
Suitable for joining Enphase Q cable up to 4 core.
Modem to use the mobile phone network to communicate with either an Enphase or SolarEdge system.
The Sunny Home Manager 2.0 monitors all energy flows in the home, automatically identifies potential savings and facilitates efficient use of solar energy
The SMA Energy Meter measures data on grid feed-in and purchased electricity as well as PV generation by other PV inverters.
In combination with the Sunny Portal powered by ennexOS, the Data Manager M enables monitoring, management and grid power control in SMA PV systems
AUD Power supply unit for the SMA Cluster Controller, SMA Data Manager M, SMA COM Gateway and SMA Inverter Manager, top-hat rail mounted.
Use Power Line Communication bridges if the Envoy needs to be located away from the broadband router and WiFi is unavailable
200 amp CT suitable for Enphase Envoy-S Metered + DRM
ACSolar
Warehouse
EXCLUSIVE
80 amp CT suitable for Enphase Envoy-S Metered + DRM
AC Solar Warehouse AC Battery label kits are fully compliant with relevant standards.
The SolarEdge 1000A Current Transformers (CT) are used with the SolarEdge Modbus Meter to monitor energy usage.
The SolarEdge 1000A Current Transformers (CT) are used with the SolarEdge Modbus Meter to monitor energy usage.
100 amp CT suitable for Enphase Envoy-S Metered + DRM
ACSolar
Warehouse
EXCLUSIVE
400 amp CT suitable for Enphase Envoy-S Metered + DRM
The wind sensor provides highly accurate and robust wind horizontal velocity measurements.
The irradiance sensor is a high-quality solar cell. It measures solar irradiance levels for photovoltaic systems.
The firefighter gateway provides centralised safety management of SolarEdge systems.
Single phase AC isolator for use on Enphase and SolarEdge solar systems
ACSolar
Warehouse
EXCLUSIVE
The SolarEdge DC junction box is a pre-assembled weather-proof enclosure used to combine DC circuits on the roof. Allowing a single DC circuit to be run to the inverter.
AC Solar Warehouse SolarEdge label kits are fully compliant with relevant standards.
AC Solar Warehouse LG Chem battery label kits are fully compliant with relevant standards.
The Enphase Q Cable and accessories are part of the seventh generation Enphase IQ System.
The Enphase Q Cable and accessories are part of the seventh generation Enphase IQ System.
The Enphase Q Cable and accessories are part of the seventh generation Enphase IQ System.
Relay controller for voltage/frequency compliance for three-phase systems
Enphase Q Cable male field-wireable connector requires MC4 crimp tool for connections to Q Cable or RAW Q Cable
Enphase Q Cable female field-wireable connector requires MC4 crimp tool for connections to Q Cable or RAW Q Cable
Relay controller for voltage/frequency compliance for single-phase systems
The Enphase Q Cable and accessories are part of the seventh generation Enphase IQ System.
Sealing cap for unused Q cable connectors
Terminator cap for unused cable ends
ACSolar
Warehouse
EXCLUSIVE
Provides an IP68 rated terminator for a multicore 2.5mm2 cable. Suitable for Enphase Q cable up to 4 core.
ACSolar
Warehouse
EXCLUSIVE
These glands have been designed specifically for Enphase IQ7 installations. One hole is sized for the AC Q cable and the other for a 4mm earth bond to the rails.
Three phase AC isolator for use on Enphase and SolarEdge solar systems
The module temperature sensor measures the temperature at the back of the photovoltaic panel.
Enphase Q Cable disconnect tool for Q Cable connectors, MC4 and Amphenol DC connectors, and AC module mount
High-quality DC cable for use on domestic solar, commercial solar and solar farms. Flexible with easy-to-strip insulation for fast installation
The DC surge protector is connected to the DC cabling of SolarEdge HD Wave single-phase inverters from 2.5kW to 10kW.
High-quality DC cable for use on domestic solar, commercial solar and solar farms. Flexible with easy-to-strip insulation for fast installation
Includes labels as per requirements for the Clean Energy Council Energy storage installation guidelines
An optional addition to the Eguana Evolve battery to provide PV production monitoring for inverters that do not directly interface with the battery.
Includes 20m of CT cabling. Used to measure & monitor the PV production of the existing solar
Nylon coated stainless steel cable ties used to secure both DC and AC cabling to racking rail
100A 3 phase CT clamp set for sonnenBatterie
The DC surge protector is connected to the DC cabling of SolarEdge three-phase inverters. The DC surge protector reduces faults in inverters and DC optimisers
Plinth is used to raise the height of the sonnenBatterie LFP2 battery cabinet if required
sonnen 200A 3 phase CT clamp set
The SolarEdge Control and Communication Gateway expands the SolarEdge monitoring and control capabilities.
The RS485 Expansion Kit provides an additional RS485 port for enhanced communications.
The SolarEdge 250A Current Transformers (CT) are used with the SolarEdge Modbus Meter to monitor energy usage.
For use with SolarEdge device control range: Immersion heater controller, AC switch with meter, and Dry contact switch
The Wi-Fi Communication Solution enables wireless communication between the SolarEdge inverter and any Wi-Fi router.
The external antenna is used to wirelessly connect SetApp-enabled SolarEdge inverters to the monitoring platform or to smart energy products.
The SolarEdge Modbus meter is used for production, consumption or import/export monitoring and for Export Limitation.
The Enphase® Envoy-S Metered communications gateway delivers solar production and energy consumption data to Enphase® Enlighten monitoring and analysis software for comprehensive, remote maintenance and management of the Enphase System.
The Enphase Mobile Connect cellular modem and data plan provide easy and reliable networking of an Enphase System without needing to rely on an internet connection at the site.
The switchboard labels required for AC Solar systems are different to those used with conventional DC systems. This kit contains all of the labels normally required for installations in all states, and complies with the requirements of the latest revision of AS5033.